The third 5G Processing Industry Chain Exhibition

With a new network architecture, 5G provides up to ten times the peak rate of 4G, millisecond transmission delay and 100 billion level connection capability, opening a new era of extensive interconnection of everything and deep human-machine interaction. 2020 will usher in the climax of 5G construction, the realization of 5G commercial scale, base station construction is in full swing, which has led to the rapid development of high-frequency high-speed materials and components, 5G materials market is broad, of which ceramic filters with its excellent performance or will become the mainstream of 5G filters.

At the same time, the accelerated construction of 5G will also promote the outbreak of 5G mobile phone market, there may be 5G thousand yuan machine in 2020, plastic mobile phone shell has become the mainstream of low-end has become a fact, and it is constantly advancing in overseas markets, in addition, ceramics with good no signal shielding has become one of the mainstream materials of 5G mobile phone cover.

Ceramic filter: dielectric ceramic powder, alumina, zirconia, magnesium hydroxide, titanate, rare earth oxide, electronic paste, PIN pin, carrier tape packaging, conductive cloth, PCB, auxiliary consumables, refractory materials, etc.

Equipment required to manufacture ceramic filters:

Sand mill, spray granulation, dry press, injection molding machine, mold, fine carving machine, sintering furnace, grinding and polishing equipment, silver spraying machine, silver dipping machine, coating equipment, printing, electroplating, silver drying furnace, silver burning furnace, laser equipment, network analyzer, coating detection, dispensing, welding, testing, automation equipment, measuring machine, etc.;

1. special internal design (patent No. : ZL 2016 1 0005463.6 replaceable rotor rotor components and installed with the rotor components of the grinder) Special rotor structure design, number and volume, to achieve the maximum specific grinding energy, can improve material grinding efficiency;

The mixing rod is a bar type rather than a cylinder type, so that the grinding bead more fully impact the material, so that the contact area between the mixing rod and the grinding bead is larger, so that the fineness is better; The rotor is assembled, convenient maintenance, low cost;

2. mixing rod special structure (patent number:ZL201820541629.0 Rod and pin sanding machine ZL201820541639.4 Eccentric rod and pin sanding machine) Due to the special design of the stirring rod, it produces the thrust of the feed port during the grinding process, so that the grinding beads are not easy to accumulate in the discharge port.The grinding bead is evenly distributed, and the grinding efficiency is more balanced.

There is a hollow rotor outside the filter screen, and there is a centrifugal groove on the rotor, which produces an outward centrifugal force during the rotation process, and large particles are thrown outward without contacting the filter screen, while small materials are discharged through the screen screen.

3. can achieve excellent grinding fineness

The material can reach the nanometer level, and the minimum fineness can reach less than 80nm by the third party Marvin laser particle size tester, and the particle is stable. Smaller grinding beads can be added with non-screen equipment: 0.03mm, the bead filling rate can reach 80-85%, the higher the filling rate, the energy density of the grinding equipment will also increase. In the same volume of grinding cavity, the higher the bead filling rate, the better the fineness, and the higher the line speed. Linear velocity is the category that determines the particle size of the grinding material.

4．high efficiency and low consumption (Patent number: ZL 2018 2 0541378.6 High efficiency rod pin sanding machine)

Fast discharge, no clogging, compared with similar products in the same industry can improve the efficiency of about 30%

5．large flow

The diameter of the filter is large, the length is long, the length of the filter is more than half the length of the rotor, and the flow area is large.

6.  high linear speed

The rotor shape is short and thick, and the line speed achieved by the company's WSP series sander is higher at the same speed.

7.  Perfect after-sales system

All the products sold by the company are guaranteed for one year, the warranty period is free on-site service, the company has professional after-sales service personnel, can respond in a timely manner, in the fastest time to provide you with solutions.